Все аналоги
Полный отчётТехнические параметры
| Питание | |
|---|---|
| No-load supply current | I 0 | ≤ 15 mA |
| Off-state current | I r | 0 ... 0.5 mA typ. 60 µA at 25 °C |
| Operating current | I L | 0 ... 200 mA |
| Operating voltage | U B | 10 ... 30 V DC |
| Rated impulse withstand voltage | U imp | 800 V |
| Rated insulation voltage | U i | 60 V |
| Rated insulation voltage U i 60 V Rated impulse withstand voltage U imp 800 V | Rated insulation voltage | U i | 60 V | Rated impulse withstand voltage | U imp | 800 V |
| Voltage drop | U d | ≤ 0.5 V |
| Характеристики по постоянному и переменному току | |
| Switching frequency | f | 0 ... 1500 Hz (switch point mode) 0 ... 150 Hz (window mode, switch point mode with stability alarm) |
| Time delay before availability | t v | max. 150 ms |
| Условия эксплуатации и корпус | |
| Ambient temperature | -25 ... 70 °C (-13 ... 158 °F) |
| Storage temperature | -40 ... 85 °C (-40 ... 185 °F) |
| Другое | |
| Alternating magnetic field | B | 200 mT |
| Assured operating distance | s a | 0 ... 6.48 mm |
| CCC approval | CCC approval / marking not required for products rated ≤36 V |
| Compatible master port type | A |
| Connection type | Connector plug |
| Constant magnetic field | B | 200 mT |
| Default setting | operating mode = switch point mode with stability alarm switching function = Normally open (NO) switching distance = 8 mm |
| Degree of protection | IP67 |
| Device ID | 0x201112 (2101522) |
| Diagnostic Coverage (DC) | 0 % |
| Diameter | 18 mm |
| Housing material | Brass, PTFE coated |
| Hysteresis | H | typ. 3 % |
| Installation | flush |
| Interface type | IO-Link ( via C/Q = pin 4 ) |
| IO-Link revision | 1.1 |
| Length | 55 mm |
| Length 55 mm Diameter 18 mm | Length | 55 mm | Diameter | 18 mm |
| Mass | 54 g |
| Min. cycle time | 2.3 ms |
| Mission Time (T M ) | 20 a |
| MTTF d | 362 a |
| Near operating distance | 5 mm (can be activated by software) |
| Number of pins | 3 |
| Output polarity | DC |
| Output type | PNP |
| Process data width | Process data input (control system side): 2 Bit Process data output (control system side): none |
| Protection class | II |
| Rated operating distance | s n | 8 mm (factory setting) |
| Reduction factor r 304 | 1 |
| Reduction factor r Al | 1 |
| Reduction factor r Cu | 1 |
| Reduction factor r St37 | 1 |
| Reverse polarity protection | reverse polarity protected |
| Scope of delivery | 2 self locking nuts in scope of delivery |
| Sensing face | PPS |
| Short-circuit protection | pulsing |
| SIO mode support | yes |
| Standards | EN IEC 60947-5-2 |
| Standards EN IEC 60947-5-2 | Standards | EN IEC 60947-5-2 |
| Status indicator | Multihole-LED, yellow |
| Switching function | Normally open/closed (NO/NC) programmable |
| Threading | M12 x 1 |
| Threading M12 x 1 Number of pins 3 | Threading | M12 x 1 | Number of pins | 3 |
| Transfer rate | COM2 (38.4 kBit/s) |
| UL approval | cULus Listed Load Type: General Purpose Circuitry: Class 2 Power Source Enclosure Type Rating: Type 1 Supply/Switching Voltage: 30 V DC Output Switching Current: 200 mA |
Изображения
Документы
К этому компоненту пока не привязаны документы.